DE     JP     EN     HU      BBlogger      Facebook      YouTube      Newsletter

0 Produkt(e)
DeepSkyPro2600 mono 26MP (IMX571 back-illuminated) APS-C cooled astrocamera

Marke:  -Lacerta
Type: CMOS-mono
Chip diagonal: 28,4mm
Resolution: 26MP
Transportgewicht:  1kg (Versandkosten)
EAN Code: 

Wien: Vorbestellen möglich
Linz: Vorbestellen möglich
Lager: bitte anfragen!

Woanders billiger? weiter...
2072.00 EUR

(inkl. MWSt)
zzgl. Versand

Warenkorb anschauen:
0 Produkt(e)
Total 0 EUR

DeepSky Pro 2600m monochrome camera

The new sensational SONY EXMOR IMX571 chip is used, which has ideal characteristics for astrophotography:

    extreme sensitivity thanks to the backside illumination technology
    very low readout noise of 0.7-3.5 e- (depending on gain setting)
    very low dark current of 0.0005e- (per pixel and second, at -20°C)
    no more visible amplifier glow - clean raw images
    native 16 bit A/D converter
    high fullwell capacity of the pixels - less burned out stars

Sensor specification IMX571:

    pixel size 3.76x3.76µm
    sensor size 23.48x15.67mm, 6224x4168 pixels, 26MP
    Exposure times 0.1ms to 3600s
    Binning modes 1x1, 2x2, 3x3
    readout speeds 6.8fps@6224x4168(16bit), 14fps@6224x4168, 37fps@3104x2048, 110fps2064x1388

The manufacturer Touptek has been a proven partner for microscope cameras for a long time and delivers sophisticated software and drivers. The camera has a very good electronics built in, which brings the advantages of the sensor fully into the picture.

Camera features:

    Gain and offset are separately adjustable to be prepared for high dynamic range as well as for lowest readout noise at short exposures. We recommend Gain zero and Offset 100 as basic settings, and in addition LowConversionGain for highest dynamic range, and HighConversionGain for high sensitivity with little dynamic range loss.
    The 2-stage adjustable Peltier cooling is powerful enough to really cool a full 42 degrees below ambient - enough even for hot summer nights.
    A window heater is built in, good for humid fall nights to keep the camera window from fogging up.
    An external desiccant cartridge can be attached to draw moisture out of the sealed camera body.
    On the back of the camera are red LEDs for status indication, and a USB hub with 2 USB2 ports, in addition to the USB3 camera port.
    Connection T2 female thread with back focus to sensor 17,5mm

Our side-by-side tests with other cameras using the IMX571 show the excellent quality of the DSPro2600.
The connection with APT, SharpCap and other control programs succeeds without problems via the Ascom driver.
The included program ToupSky offers extensive functionalities and is excellent also for planetary imaging, it can display raw images also pre-debayed with correct colors (white balance).

The drivers are installed with the ToupSky software, please download Ascom and DirectShow drivers from the support folder:

Drying process to prevent icing of the sensor:

    the desiccant are small silica gel beads in a small tube (included)
    carefully remove the stubble at the back (otherwise the beads will roll out) and place them in a small paper boat
    put the paper boat with the beads into the microwave and bake them for 4x 30 seconds
    then return with the beads into the tube, and screw it to the camera (where it says: do not open).
    leave the whole thing for a day - you can also plug in the camera and let it read out so that it gets a little warm and the moisture evaporates better (but do not cool it!).
    Immediately after unscrewing the camera with seal on the screw cleanly close again.

Scope of delivery:

    waterproof Peli Case made of impact resistant plastic
    DSPro2600 monochrome camera
    Power supply 100-250V/3A
    Dry cartridge with silica gel
    Software and driver CD


Wir empfehlen auch:
Wir empfehlen auch: